74L00 – Find the PDF Datasheet, Specifications, OEM and Distributor Information. Cross Reference Powered by Datasheets 74LS00, 74LS00 Datasheet, 74LS00 Quad 2-Input NAND Gate, buy 74LS00, 74LS00 ic. Rev. 7 — 25 November Product data sheet. Table 1. Ordering information. Type number Package. Temperature range Name. Description. Version.

Author: Voodoolkis Shagal
Country: Tunisia
Language: English (Spanish)
Genre: Finance
Published (Last): 12 March 2011
Pages: 96
PDF File Size: 15.80 Mb
ePub File Size: 20.35 Mb
ISBN: 669-5-54635-610-6
Downloads: 6303
Price: Free* [*Free Regsitration Required]
Uploader: Moogukinos

Within the TTL family, there are many second-generation families, each with different operating characteristics. TTL is a bipolar process in which npn transistors operate mostly in the “saturated” and “cutoff” regions of their operating curves. Data sheets for a chip list ICCsupply current for a chip with the understanding of no load on the output pins.

The time-varying voltage from the power company is converted to steady “DC” voltage in a power supply. It can be measured or calculated for a hardware system with various data paths.

Datassheet logic and propagation delay. Sometimes a minimum delay is cause for concern, to prevent race conditions in flip flop circuits. CMOS chips filled a niche in battery-operated devices, where voltage would slowly decline over the life of the battery. A passive device which absorbs power gets warm.

54L00/74L00 datasheet & applicatoin notes – Datasheet Archive

An open-collector output has current sinking capabilities, that is, it can present a logic-LO output. Why the concern about power consumption? TTL is a saturating bipolar ratasheet. Open-Collector Output Figure 6. Faster hardware is better, all other things being equal. These two tend to be directly related, i. It takes extra time to remove charge from the thin base region.


The designer may have to search for minimum and maximum delays.

This chapter on dynamic parameters extends our look at data sheets to what are called “AC characteristics”-various propagation delays and timing requirements.

Link to End of chapter Exercises:. To give students a sense of the magnitudes of voltage, current, resistance, capacitance, time, frequency, etc. The oxide is silicon dioxide, a hard insulating material. Recall from mechanics that energy or work is force x distance.

ECL gates can be thought of as current mode devices, dqtasheet current flows through one or another arm of the differential pair, depending on the state of the circuit. In commercial ECL families 10K is the most popular the power supply is actually That is, from Ohm’s Law one talks about 1 datashete across 1 ohm produces 1 ampere.

The faster the transition from one state to the other by a switch, the more current transients generated by the switch and throw noise either as local E-M radiation, or a power supply glitches into the neighboring system.

What is the minimum and maximum frequency of oscillation?

Catastrophic failure from heat is not the only concern. The CMOS process is applied widely to memories, microprocessors and gate arrays-the kinds of “LSI” chips not generally considered in a particular logic family. Does this input constitute a logic LO or logic HI input? An unconnected input is said to be floating. Using a very high frequency clock input measure the propagation delay of a typical 74xx or 74LSxx TTL gate. Observe here that the circuit elements associated with Q4 in the totem-pole circuit are missing and the collector of Q3 is left open-circuited, hence the name open-collector.

  78L05 SOT 89 PDF

Why is negative logic commonly used? The first CMOS family, the series chips, averaged just nanowatts quiescent power per gate and tolerated voltages as low as 3 and as high as 18 volts for VCC. The power company and a “power supply” are aptly named, although a power supply normally transforms AC into DC, and is not a primary generator of electrical power, as the rotating machinery of a power plant is.

7400 / 74xxx TTL Series ICs

And see Nature The region can be modeled by a parasitic junction capacitance, shown in 74l0 figure below. Construct and test this circuit. The basic ECL inverter design, shown below, starts with a transistor over an emitter resistor, like we’ve seen in the TTL splitter.

Some chips, particularly display drivers like themay get hot to the touch because they’re consuming a lot of power for their small size, datashert current out to display segments-an “8” signal should feel hotter than a “1. What is the smallest value of R such that the output is still LO?

We’ll see in this chpt. Perhaps the elusive blue LED could be constructed on diamond substrate. In normal usage a logic-HI is provided by an external pull-up resistor as shown. Power is the rate dataseet energy production or consumption. CMOS memory chips with 64 million transistors have been fabricated.