ASTM A – Designation: A – 10 Standard Speci?cation for Stainless Steel Bars and Shapes1 T. This standard is issued under the fixed designation A ; the 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel. ASTM Aa. November 1, Standard Specification for Stainless Steel Bars and Shapes. This specification covers hot-finished or cold-finished bars .

Author: Kagajas Moogugul
Country: Qatar
Language: English (Spanish)
Genre: Art
Published (Last): 3 May 2011
Pages: 362
PDF File Size: 3.53 Mb
ePub File Size: 17.15 Mb
ISBN: 601-9-98254-423-5
Downloads: 79820
Price: Free* [*Free Regsitration Required]
Uploader: Shagami

A — 10 Standard Speci? A number in parentheses indicates asrm year of last reapproval. This standard has been approved for use by agencies of the Department of Defense.

astm a round bar, astm a rounds, astm a hex bar, astm a rod

It includes rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels. The free-machining types Note 2 for general corrosion resistance and high-temperature service are covered in a separate speci? NOTE 3—There are standards covering high nickel, chromium, austenitic corrosion, and heat resisting alloy materials.

Such requirements may include but are not limited to the following: NOTE 4—A typical ordering description is as follows: The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Current edition approved May 1, Originally approved in Last previous a276-13s approved in as A — 08a.


Maximum, unless range or minimum is indicated. C For some applications, the substitution of Type L for Typeor Type L for Type may be undesirable because of design, fabrication, or service requirements. In such cases, the purchaser should so indicate on the order.

ASTM A – 13a Standard Specification for Stainless Steel Bars and Shapes

D Nitrogen content is to be reported for this grade. F Nickel plus copper shall be 0. Ast, Product analysis tolerance over the maximum limit for carbon and nitrogen shall be 0. Mechanical Properties Requirements 6. Failure to comply with the general requirements of Speci?

A T T Hhot-? Yield Strength,A min ksi 40 Elongation in 2 in. An alternative method of determining yield strength may be used based on a total extension under load of 0. B For some speci?

The use of sub-size test specimens, when necessary, is permissible in accordance with Test Methods and De? C Reduction of area does not apply on? D The material shall be capable of meeting the required reduction of area where listed, but actual measurement and reporting of the reduction of area are not required unless speci?

ASTM A276 Round Bar

E Or equivalent Rockwell hardness. G For shapes having section thickness of 1? Approved May 1, ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such asttm rights, and the risk of infringement of such rights, are entirely their own responsibility.


ASTM A276 Specification

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Your comments are invited either for revision of this standard a276-13 for additional standards and should be addressed to ASTM International Headquarters.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

Permission rights to asym the standard may also be secured from the ASTM website www.