ASTM C114 PDF

C – 00 Standard Test Methods for Chemical Analysis of Hydraulic Cement, chemical analysis, compositional analysis, hydraulic cements. ASTM Standards: 2. C 25 Test Methods for Chemical Analysis of Limestone,. Quicklime, and Hydrated Lime. D Specification for Reagent Water. ASTM C accreditation for cement analysis . are within the prescribed limits for iron, so acceptable (according to ASTM-C requirement).

Author: Dok Zululabar
Country: Venezuela
Language: English (Spanish)
Genre: Photos
Published (Last): 1 April 2006
Pages: 390
PDF File Size: 13.19 Mb
ePub File Size: 2.10 Mb
ISBN: 567-4-96902-400-5
Downloads: 78832
Price: Free* [*Free Regsitration Required]
Uploader: Tozragore

Description of Referee Analyses. Reporting of analyses shall be of the following order: Standard A by the mass fraction of Standard A in each of the other standards that is, 0.

These test methods cover the chemical analyses of hydraulic cements. The reference test methods are long accepted wet chemical test methods which provide a reasonably well-integrated basic scheme of analysis for hydraulic cements.

Link to Active This link will always route to the current Active version of the standard.

Description of Referee Analyses. Specific chemical test methods are provided for ease of reference for those desiring to use them.

A number in parentheses indicates the year of last reapproval. The reference cement is acceptable if its assigned value agrees with the average referee value within the limits given in column 3 of Table 1. Alternative test methods and procedures include determination of calcium oxide, calcium dioxide, magnesium oxide, loss on ignition, titanium dioxide, phosphorus pentoxide, manganic oxide, and free calcium oxide.

These reagents shall sstm purity agents, water, repackaged reagents, concentrated acids and ammonium hydroxide, nonstandardized solutions, and indicator solutions. Originally approved in Longer, more complex procedures, in some instances, have been retained as alternative test methods to permit comparison of results by different procedures or for use when unusual materials are being examined, where unusual interferences satm be suspected, or when unusual preparation for analysis is required.

  BRECHT THE RESISTIBLE RISE OF ARTURO UI PDF

The standardization used for qualification and for analysis of each constituent shall be determined by valid curve-fitting procedures. Link to Active This link will always route to the current Active version of the standard. Such demonstration may be made concurrently with analysis of the cement being tested. General procedures include sample asgm, taring of asmt, weighing of ignited residues, volatilization of platinum, chemical analyses, and calculation.

Requirements for Qualification Testing. Performance Requirements for Rapid Test Methods.

ASTM C114 – 15 – Chemical Analysis of Hydraulic Cement

NOTE 3—It is not intended that the use of reference test methods be confined to referee analysis. C Interelement corrections may be used for any oxide standardization provided improved accuracy can be demonstrated when the correction is applied to all seven CRM cements.

F Demonstrate performance by analysis, in duplicate, of at least one Portland cement. A reference test method must be used where an alternative test method is not provided.

Last previous edition approved in as C — It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

ASTM C – 00 Standard Test Methods for Chemical Analysis of Hydraulic Cement

Requalification of the analyst is required every two years. Prepare three standards, each in duplicate: Requirements for Qualification Testing.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Any test methods of demonstrated acceptable precision and bias may be used for analysis of hydraulic cements, including analyses for referee and certification purposes, as explained in Section 4.

The reference cement must have an assigned value for the analyte being determined. Standard reagents for the test method shall be used within the limits of the specification. Qualification for Different Analyses. The final results, when corrected for blank values, should, in either case, be so designated. Specific chemical test methods are grouped as reference test methods and alternative d114 methods.

  EMMA GOLDMAN HAYATM YAARKEN PDF

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The alternative test methods generally provide individual determination of specific analytes and may be used alone or as alternates and determinations within the basic scheme at the option of the analyst and as indicated in the individual method.

Any test methods of demonstrated acceptable precision and bias may be used for analysis of hydraulic c14, including analyses for referee and certification purposes, as explained in Section 3.

Acceptable reference cements are NIST. The x114 for qualification of a test method and analyst are summarized in Table 2. Reference test methods and procedures include determination of insoluble residue, silicon dioxide, ammonium hydroxide group, ferric oxide, phosphorus pentoxide, titanium dioxide, zinc oxide, aluminum oxide, calcium oxide, magnesium oxide, sulfur, loss on ignition, sodium and potassium oxides, manganic oxide, chloride, chloroform-soluble organic substances.

Specific chemical c1114 methods are provided for ease of reference for those desiring to use them. The alternative test methods generally provide individual determination of specific analytes and may be used alone or as alternates and determinations within the basic scheme at the option of the analyst and as indicated in the individual method. Sample preparation and general test procedures shall be followed according to the specification.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.