BC558 TRANSISTOR DATASHEET PDF

DataSheet: PDF icon BCPDF. BC is a general purpose PNP transistor. It is used in switching and amplifier applications. The DC current gain varies in. BC Transistor Datasheet pdf, BC Equivalent. Parameters and Characteristics. Semiconductor data sheets and/or specifications can and do vary in different applications . BC / BC / BC VCE = -5 V, IC = µA.

Author: Mosida Tajinn
Country: Barbados
Language: English (Spanish)
Genre: Politics
Published (Last): 3 July 2009
Pages: 107
PDF File Size: 16.74 Mb
ePub File Size: 13.97 Mb
ISBN: 531-6-73280-764-4
Downloads: 65464
Price: Free* [*Free Regsitration Required]
Uploader: Grojas

SPI Module of Arduino. A Transistors acts as an Amplifier when operating in Active Region. In the below GIF you can notice the transistor being switched for a low voltage 1v audio signal.

In the absence of base signal, it gets completely dagasheet.

The value of this resistor RB can be calculated using below formulae. Virgin Galactic — Commercial Space Flight.

BC Pinout, Configuration, Circuit As Switch & Amplifier

The BC because of this large gain value is normally used to as a audio amplifier. BC is a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at ground and will be dxtasheet Reverse biased when a signal is provided to base pin. Skip to main content. Arduino based GPS receiver. It is also used as a complement for transistors BC to BC When uses as an Amplifier the DC current gain of datashet Transistor can be calculated by using the below formulae.

  LEUCEMIA PROMIELOCITICA PDF

Submitted by admin on 26 March The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves. This high-density System-in-Package SiP integrates controller, power switches, and support components. For switching applications, transistor is biased so that it remains fully on if there is a signal at its base.

Where an input signal of low voltage is amplified tranxistor to high voltages t0 drive loads like speakers. As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin.

For amplification applications, the transistor is biased such that it is partly on for all input conditions. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

BC558 Datasheet, Equivalent, Cross Reference Search

TL — Programmable Reference Voltage. Interface GPS with Arduino. Choosing Battery for Robots. Also note that a PNP transistor is always used for high side switching, meaning the transistpr is connected to power and emitter to load that is to be switched. BC as switch When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.

  BPT VLS 101 PDF

BC is used in common emitter configuration for amplifiers.

HTTP This page has been moved

It can amplify power, voltage and current at different configurations. Of the above types common emitter type which amplifies voltage bx558 the popular and mostly used configuration.

Complete Technical Details can be found in the BC datasheet given at the end of this page. Choosing Motor For Robots. The voltage divider is the commonly used biasing mode.

A resistor is always added in series with base pin to limit the base current. BC has transiztor gain value of to ; this value determines the amplification translstor of the transistor. Interface SD Card with Arduino. The DC current gain varies in range to What is Web Browser.

BC is a general purpose PNP transistor. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. Amplifier modules like Audio amplifiers, signal Amplifier etc. When this transistor is fully biased then it can allow continues current of mA to flow across the collector and emitter.

The input signal at bx558 is amplified and taken at the emitter. This is known as the biasing.

It is used in switching and amplifier applications.