DENSEN DM 10 PDF

Densen DM (£). “The Densen sounds excatly as it looks – big and lush. You’ll never find music thin or insubstantial if you’ve got one plugged in.”. Specifications. Power output: 75 watts per channel into 8Ω (stereo). Frequency response: 2Hz to kHz. Total harmonic distortion: %. Input sensitivity. Densen Audio DM Integrated Amplifier. Integrated pre- amp/power amp, 75 watts rms output per channel into 8 Ohms, four line-level inputs, two tape inputs.

Author: Akinokazahn Zurr
Country: El Salvador
Language: English (Spanish)
Genre: Music
Published (Last): 26 April 2004
Pages: 469
PDF File Size: 1.13 Mb
ePub File Size: 4.35 Mb
ISBN: 583-4-72442-779-7
Downloads: 26861
Price: Free* [*Free Regsitration Required]
Uploader: Talar

In other words, they can only be used for tape recording and playback rather than for a “loop” containing an equalizer for tone control or other circuit such as a surround sound processor. Negative feedback can produce distortion of its own, however, and too much of it becomes obvious when listening to sibilants the “s” in wordswhere it sounds as if someone is hissing at you.

Because the DM and B use no global negative feedback, the damping factor is very modest. This not only results in a reduction in the problems listed above, which are normally corrected by the use of negative feedback, but also improves phase linearity and speed. They are probably the result of even order harmonic distortion – a hallmark of the SET – that do not occur to any significant degree in the Densen amplifiers.

The upper portion of the audio spectrum is laid back, not quite as much as the SET, but just a little, and the mid-range is glorious, just like the SET. For the DM, there are 40, microfarads of capacitance for the input stages and the same for the output, while the B uses 10, microfarads for the input, and 30, for the output.

  APC BR1500 PDF

Densen DM10 MKII Stereo Integrated Amplifier | eBay

Thomas Sillesen, the designer of the Densen line, was there to answer our many questions about this unique amplifier. Each amp is black with large brass knobs.

Both the DM and the B are among the finest integrated amplifiers we have ever heard.

In other words, they can only be used for tape recording and playback rather than for a “loop” containing an equalizer for tone control or other circuit such as a surround sound processor. The basic difference between the DM and B is in dynamic range, and perhaps a bit in the detail of the upper mid-range as well as the high end. Each amp is black with large brass knobs. The basic difference between the DM and B is in dynamic range, and perhaps a bit in the detail of the upper mid-range as well as the high end.

Densen DM10 MKII Stereo Integrated Amplifier

The tape inputs and outputs are not tape loops. The DM uses two toroidal transformers one for each channeland the B uses one which supplies both channels. Please explain the problem you are having. Audiocostruzioni e punto vendita di: Thomas Sillesen, the designer of the Densen line, was there to answer our many questions about this unique amplifier.

Unpacking the amplifiers is an experience in itself. Their elegant sound is dnsen only by their looks. This not only results in a reduction in densne problems listed above, which are normally corrected by the use of denden feedback, but also improves phase linearity and speed.

The sibilants are clean, and female voices a good test for an amplifier are sweet and untainted. The sound of the DM and B is somewhat like a single ended triode tube SET amplifier, and that is a complement indeed.

Product Review –

Unpacking the amplifiers is an experience in itself. Since the DM and B are designed with the shortest signal path in mind, tape loops are out of the picture. However, either amplifier sm be used with a surround sound processor if the processor has the capability of routing the unprocessed signal through when it is turned off.

  LINKSYS WRT54G2 V1 MANUAL PDF

Even harsh CDs are mellow when played through a Densen, just like a SET, and yet the volume is there when desired because high current is available the SET typically has an output of only 7 – 12 watts per channel.

Both the DM and the B are among the finest integrated amplifiers we have ever heard. Therefore, good speaker cables with low capacitance should be chosen for the best performance.

Densen DM 10

The use of a loop would require a tape monitor switch, and this would mean that the signal path has to be routed through the switch. The amplifiers are built partially by censen, and partially by hand assembly. A red LED in between the two brass control desen illuminates when the units are on, and slowly fades when turned off. However, either amplifier can be used with a surround sound processor if the processor has the capability of routing the unprocessed signal through when it is turned off.

The use of a loop would require a tape monitor switch, fm this would mean that the signal path has to be routed through the switch. The box and foam rubber protection weigh as much as some amplifiers! One of the most important design characteristics of these amplifiers is the lack of global negative feedback.