EPEC 2024 PDF
Epec CAN Module Family CONTROL MODULE G08 / MAN DOCUMENT VERSION HISTORY Date Notes Document . Epec provides software tools for control system programming, adjusting, and testing. From the systems engineering viewpoint, it is not enough to have sufficient. Open and compatible. Embedded control systems are based on PLCopen and CANopen®, which make them easily scalable to meet requirements for both.
|Published (Last):||8 April 2012|
|PDF File Size:||4.43 Mb|
|ePub File Size:||11.66 Mb|
|Price:||Free* [*Free Regsitration Required]|
Gold plated, locked and sealed connectors: Digital outputs can be configured to be used as digital inputs and vice versa. Violating this rating may lead 2042 system not recognizing all input state transitions Note 2: Module position Mounting base Mounting base Module position?
Maximum pulse input frequency 20 kHz. Puncture hole fastening 7. This feature makes it possible to detect short circuits to the ground. Pins of this kind can be used as e.
An external fuse should be installed for the product or the system power supply.
Epec Control Module, Epec Control Module Suppliers and Manufacturers at
The warranty does not cover possible expenses relating to travelling, accommodation, daily benefits, etc. Please refer CoDeSys 2.
In other words, pins connect the load to the ground. Module has a shutdown circuit which protects the module and loads against overvoltage. In carefully selected applications these pins can also be used as digital inputs. It must be taken care in system design that the output unintentionally switching to on state causes no harm to system. Any of these inputs can be logically paired with another similar input.
The manufacturer shall, at its sole option, repair rpec products at its manufactory eppec Sein? CANopen for all physical buses? No saving operations program flashing or parameter storing into permanent memory can be done under 11,5 VDC. Maximum code size kb. It means that to be able to reach the maximum frequencies, there is no room for application program or any other processes like CAN traffic.
Nothing prevents using these pins to measure currents from other sources as well. Test method EN ?
In high impedance voltage input configuration they have low threshold voltage which is quite sensitive to interference signals. Violating this rating may lead to application program not noticing all input state transitions Epec Oy reserves all rights for improvements without prior notice Epec Oy Matinkatu 6 FIN Sein?
2042 are, for example, outputs which source current and outputs which sink current. A separate safety analysis is always recommended for the machine and its control system. Some of the inputs are grouped: Open loads can not be detected because the internal load resistor is connected to the ground.
For more information refer to programming manuals. Otherwise operation of other inputs may be interfered Note 3: Applies to inputs used as normal digital inputs. All conditions must be respected.
Violating this rating may lead to system not recognizing all input state transitions. Neither does the warranty cover the expenses of sending devices to or from the manufacturer for repairs. A small and protective module casing keeps inside high performance microcontroller with lots of control capabilities. Inputs of this type are also suitable for quadrature sensor position counting.
Please consult the manufacturer before using this pin as a module voltage supply.
EPEC 2024 controller Manual
The setting is done by a PWM channel but setting the frequency of one channel sets also the frequencies of all the other channels in the same groups. The warranty does not cover any costs related to removing or fastening of devices related to the products. The maximum frequencies given in the table below are such frequencies which make the module to freeze in practice if all inputs are connected to their maximum frequencies.
PWM frequencies can be configured under software control in groups of outputs. Possible to add external c-programmed library? So, the practical limits are lower but the maximum values of the table still give the basis for the estimation. The manufacturer eec not assume any peec for this product being fit for any particular application, unless otherwise expressly stated in writing by the manufacturer.
All cables, connectors and tools must be of correct type and sufficiently high quality.
This makes it rather hard to estimate the actual maximum frequency of the pulses that the module is able to count reliably. Violating this rating may lead 204 application program not noticing all input state transitions. This feature makes it possible to detect open loads and short circuits to the supply voltage.
PWM capable outputs are divided into six groups. All functions return automatically to within normal limits after exposure is removed.